v1.0.0 - 2025-03-13
EHS-Sentinel has been heavily modified to incorporate the control mechanism
The read-in behavior of the modbus registers has been revised from chunks to single byte
MessageProcessor now runs asynchronously
MessageProducer added which takes over the writing communication with the WP
Configuration of HASS entities has moved from hardcoded to NASA Repository
NASA Repository has been fundamentally changed
All FSV Values, NASA_POWER, VAR_IN_TEMP_WATER_LAW_TARGET_F, NASA_INDOOR_OPMODE are allowed for writing mode
NASA_OUTDOOR_DEFROST_STEP DEFROST STEP 10 (b'0xa') added
ENUM_IN_SG_READY_MODE_STATE ACTIVE (b'0x2') added
New configuration point allowControl to allow control of the Samsung EHS heat pump (deactivated by default).
[!CAUTION]
This functionality requires that EHS-Sentinel actively communicates with the Samsung EHS, so EHS-Sentinel intervenes here in the Modbus data traffic between the components (it sends its own messages). The activation of this functionality is exclusively at your own risk. I assume no liability for any damage caused.
new configuration points in logging
controlMessage (default False) to print out the controlled mesagges
invalidPacket (default False) prints out invalid messages (length not ok, x34 not at end...)
Dashboard template has been split, ressources/dashboard_readonly_template.yaml is for readonly mode and the ressources/dashboard_controlmode_template.yaml for control mode
v0.3.0 - 2025-02-27
Added poller functionality. EHS-Sentinel can now actively request values via Modbus
fetch_intervals and groups can be defined in the config file
default group and pollers are in the sampelconfig
[!CAUTION]
This functionality requires that EHS-Sentinel actively communicates with
the Samsung EHS, so EHS-Sentinel intervenes here in the Modbus data
traffic between the components (it sends its own messages).
The activation of this functionality is exclusively at your own risk.
I assume no liability for any damage caused.
added a homeassistant dashboard.yaml with default Dashboard
edited Measurement
ENUM_IN_FSV_5061 add enums
ENUM_IN_FSV_5094 correct enum values
ENUM_IN_PV_CONTACT_STATE correct enum values
added units for multiple Measurements
Rename some Measurements:
NASA_INDOOR_COOL_MAX_SETTEMP_WATEROUT -> VAR_IN_FSV_1011
NASA_INDOOR_COOL_MIN_SETTEMP_WATEROUT -> VAR_IN_FSV_1012
NASA_INDOOR_COOL_MAX_SETTEMP_ROOM -> VAR_IN_FSV_1021
NASA_INDOOR_COOL_MIN_SETTEMP_ROOM -> VAR_IN_FSV_1022
NASA_INDOOR_HEAT_MAX_SETTEMP_WATEROUT -> VAR_IN_FSV_1031
NASA_INDOOR_HEAT_MIN_SETTEMP_WATEROUT -> VAR_IN_FSV_1032
NASA_INDOOR_HEAT_MAX_SETTEMP_ROOM -> VAR_IN_FSV_1041
NASA_INDOOR_HEAT_MIN_SETTEMP_ROOM -> VAR_IN_FSV_1042
NASA_DHW_MAX_SETTEMPLIMIT -> VAR_IN_FSV_1051
NASA_DHW_MIN_SETTEMPLIMIT -> VAR_IN_FSV_1052
NASA_USE_DHW_THERMOSTAT -> ENUM_IN_FSV_3061
NASA_USE_BOOSTER_HEATER -> ENUM_IN_FSV_3031
NASA_ENABLE_DHW -> ENUM_IN_FSV_3011
NASA_USE_THERMOSTAT!1 -> ENUM_IN_FSV_2091
NASA_USE_THERMOSTAT2 -> ENUM_IN_FSV_2092
Fixes#9
* heateroutput limit 0 - 15000 w
* heatoutput always positive
* ENUM_IN_FSV_2041 value 0c00 unknwon added
* recalculate crc6 checksum and check it
* skip exception to reduce logging
* NASAPacket and NASAMessage prepared for write mode
MQTT Auto Discovery changed single entitity to all entities
NASA Packet crc16 Checksum verificated
* - Changed MQTT Auto Discovery Config Message from single Entitiy to all Entities at ones, known devices are fully configured, not known empty (markt to delete)
- NASAPacket and NASAMessage are now bidirectional, can decode and encode Packets
- Added crc16 Checksum check for any Packet to reduce incorrect value changes
- Folling warnings moved to SkipInvalidPacketException and from warning to debug log level to reduce Logentries
- Source Adress Class out of enum
- Destination Adress Class out of enum
- Checksum for package could not be validatet calculated
- Message with structure type must have capacity of 1.
* NASA_OUTDOOR_HP as kw unit
* NASA Repository, measurements enums completed
* filter wifikit heartbeat
* process only packets from indoor or outdoor
* correct readme
* remove expire
* device discovery status
* new mqtt hass configuration approach
* added new measurements
* added new logging features from config
* NASA_EHSSENTINEL_TOTAL_COP added
* removed silentMode, added logging proccessedMessage
* loaded devices
* loaded devices counter fix
* only if retain true
* final 0.2.0 commit
* device_class: measurement for NASA_EHSSENTINEL_COP and NASA_EHSSENTINEL_HEAT_OUTPUT
* state_class: measurement for NASA_EHSSENTINEL_COP and NASA_EHSSENTINEL_HEAT_OUTPUT
* ENUM_IN_WATERPUMP_PWM_VALUE as var not enum
Unit % as = measurement
* NASA_OUTDOOR_CONTROL_WATTMETER_ALL_UNIT_ACCUM state_class: total_increasing
* NASA_OUTDOOR_CONTROL_WATTMETER_ALL_UNIT_ACCUM device_class and unit
* NASA_OUTDOOR_CONTROL_WATTMETER_ALL_UNIT_ACCUM device_class energy
* fixing ValueError and better logging for determine_value try catch
* update reqierments and rreadme for venv
* ENUM_IN_FSV_2041 enum value fixed
* large buffer log
* prevent buffer overloading
* remove await
* a
* Feature/test without buffer (#5)
* test
* test
* test
* devision by 0 error fixed
remove task print
* logger
* topic clear only on online message
* expand logging
* reduce logging
* device_class: measurement for NASA_EHSSENTINEL_COP and NASA_EHSSENTINEL_HEAT_OUTPUT
* state_class: measurement for NASA_EHSSENTINEL_COP and NASA_EHSSENTINEL_HEAT_OUTPUT
* ENUM_IN_WATERPUMP_PWM_VALUE as var not enum
Unit % as = measurement
* NASA_OUTDOOR_CONTROL_WATTMETER_ALL_UNIT_ACCUM state_class: total_increasing
* NASA_OUTDOOR_CONTROL_WATTMETER_ALL_UNIT_ACCUM device_class and unit
* NASA_OUTDOOR_CONTROL_WATTMETER_ALL_UNIT_ACCUM device_class energy
* fixing ValueError and better logging for determine_value try catch
* update reqierments and rreadme for venv
